Snowy White Putty
Water Resistant Putty
Excellent Sliky Surface Finish
Primer Free, Maintains Original Colour Tone
Perfect Solution For Dampness, Peeling Off And Flaking
Maximized Paint Life
APPLICATIONCOVERAGE CAPACITY OF SUNSHINE SUPER WALL CARE PUTTY
SUNSHINE SUPER WALL CARE PUTTY can be applied in maximum 2 coats only. Thickness of 1st coat should be 1.5mm and, Thickness of 2nd coat should be 1.0mm
On double coat of sand cement plaster(Rough Surface), SUNSHINE SUPER WALL CARE PUTTY covers:- In 15 Kgs, it covers 100 sq/ft (i.e. 1.00 brass) In 20 Kgs, it covers 133 sq/ft (i.e. 1.33 brass)
The absolute coverage earned depends on the wall surface quality and the quality of worker
SUNSHINE SUPER WALL CARE PUTTY does not contain any toxic material, then also it is recommended to use hand gloves and mask for nose and mouth while making paste or handling putty powder. If work of putty applying is stoped due to some reason and the putty paste is dried in bucket or pan, this paste is not suitable for use again(after 2 hours). This paste should be thrown away compulsory. Putty should be kept away from children. SUNSHINE SUPER WALL CARE PUTTY should be always kept in dry place and always open it immediately before using. Do not keep the putty bag open.
Curing is not required after applying of SUNSHINE SUPER WALL CARE PUTTY. But in very hot weather area little water must be sprinkle on the wall surface, it will strengthen the cement particles. Before applying SUNSHINE SUPER WALL CARE PUTTY, little water must be sprinkled on the wall surface. After first coat, the surface must be sprinkled with little water twice a day for 2 days.
Do not mix any color or Steiner in SUNSHINE SUPER WALL CARE PUTTY. If the wall is old painted, it is not suitable and good for putty application. But without color and rough surface wall is best for applying SUNSHINE SUPER WALL CARE PUTTY. SUNSHINE SUPER WALL CARE PUTTY has a whitest or silky property, it can be leaved with out painting also. If paint are used directly on SUNSHINE SUPER WALL CARE PUTTY, it consumes less color which results in low budget painting. Also paint can be applied directly on SUNSHINE SUPER WALL CARE PUTTY without using primer. The life of SUNSHINE SUPER WALL CARE PUTTY is same as that of the wall plaster below it. The wall surface looks more beautiful because of the richest whitest quality of SUNSHINE SUPER WALL CARE PUTTY. Due to white cement as base, SUNSHINE SUPER WALL CARE PUTTY has a good power and toughness in it. SUNSHINE SUPER WALL CARE PUTTY has good bonding strength, so the wall gets good toughness for long time.
PREPARATION OF SURFACEDUST OR PARTICLES
If there is present of loose particles, dirt or any traces of foreign particles on walls, clean it with sand papper or wire brush if necessary.
If the wall has Pin Holes, Crack or Heavy Unevenness, replaster it with cementitious material and cure it for 2-3 days.
If the wall already has a paint coat on it, remove the paint completely with wire brush or grinder in such a way that the interior sand plaster will be opened. When the wall is completely clean, Sprinkle little water on the wall surface where putty is to be applied.
If the wall surface on which putty is to be applied is very smooth or silky, then the putty paste will not be set properly on the particular walls. So before applying wall putty, rub the wall with fine sand paper, wire brush or grinder.
The wall must be plastered with cement plaster. It must not be plastered with Plaster of Paris or Gypsium.
During attrition (Cleaning with machine) of floor and side wise, slurry is produced. Which may bond with the walls and becomes hard if not cleaned properly. Putty applied on such surface will not give good result and after some days it will peel off, so before applying putty, the particular wall should be cleaned with sand paper or wire brush and must be washed with water to avoid peeling and peeling powder and may affect adhesion property. After drying wall, wall putty can be applied, before applying wall putty, Sprinkle little water on the wall surface.
Due to rain and leakage of walls, peeling occurs. In this condition, firstly solve the leakage problem technically and then after the wall surface should be cleaned with sand paper or wire brush. After cleaning, wall must be washed with water so that if any particles are present will wash out. Let the wall surface dry, Sprinkle little water on the wall surface, then apply wall putty.
MAKING OF PUTTY PASTE
Take a required quantity of SUNSHINE SUPER WALL CARE PUTTY in a clean pan or bucket. Add about 35-40% of water to the putty. Stir continuously by hand or electric mixer for 15-20 minutes to obtain clump free, uniform paste. Keep the paste aside for 5-10 Minutes without disturbing, so that the polymers in it can be dissolved. Re-stir the paste again and now the putty paste is ready for application.
Preapre the paste in such a quantity, which can be used within 2 hours from mixing.
In between work, if the paste is kept undisturbed for more than 30 minutes, stir the paste again for 1-2 minutes with hand stirrer or electric stirrer.
|Compressive Strength||till 28 Days|
|Compressive Strength||till 28 Days|
|Maximum Thickness Of Coat||2 – 2.5 mm|
|Coverage On smooth surface (sunlaa plaster)||In 07 Kgs, It Covers 100 sqft (i.e. – 1 brass)|
|Coverage on rough surface (sand cement plaster)||In 15 Kgs, It covers 100 sqft (i.e. – 1 brass)|
|Pot Life||2 – 3 Hours|
|Water Demand||35 – 40 %|
|Ratio of water:putty||1 : 4|